AMPLIFIER INPUT & Output

Output Voltage Range
0 to ±10 kV DC or peak AC.

Output Current Range
0 to ±60 mA DC, 0 to ±300 mA peak capability for 20 µs (see Automatic Power Limit feature for AC and DC limitations).

Input Voltage Range
0 to ±10 V DC or peak AC (inverting and differential input options are
available).

Input Impedance
25 kΩ, nominal (inverting/differential option 50 kΩ, nominal).

PERFORMANCE

DC Voltage Gain
1000 V/V.

DC Voltage Gain Accuracy
Better than 0.1% of full scale.

Offset Voltage
Less than ±4 V.

Output Noise
Less than 5 V rms (measured using the true rms feature of the Hewlett Packard Model 34401A digital multimeter).

Slew Rate (10% to 90%, typical)
Greater than 1000 V/µs.

Large Signal Bandwidth (2% distortion)
DC to greater than 7.5 kHz.

Small Signal Bandwidth (-3dB)
DC to greater than 20 kHz.

Settling Time (to 1%)
Less than 150 µs for a 0 to 10 kV step.

Stability

• Drift with Time
  Less than 50 ppm/hr, noncumulative.
• Drift with Temperature
  Less than 100 ppm/°C.

Automatic Power Limit
Automatically limits the internal power dissipation to protect the Model PD07016 from overheating . The following graph illustrates the Model PD07016 automatic power limits.

Model PD07016 Output Operating Range

PRODUCT FEATURES

DC Offset Voltage Adjustment
A potentiometer with a calibrated dial adjusts the level of the DC offset voltage from 0 to ±10 kV DC. A three (3) position switch selects positive polarity, negative polarity, or DC bias voltage off.

High-Voltage On/Off High-Voltage On/Off
Switch selectable for either local or remote control.

• Local
  Individual push-button switches.
• Remote
  A TTL compatible input. A TTL high (or open) turns off the high-voltage output. A TTL low turns on the high-voltage output.

Dynamics Adjust
A graduated one-turn panel potentiometer is used to optimize the AC response of the Model PD07016 for various load parameters.

Current Limit/Trip
Switch selectable for either limit or trip. A graduated one-turn panel potentiometer is used to adjust the limit or trip level from 0 to 60 mA.

Out of Regulation Status
An amber indicator will illuminate and a BNC will provide a TTL low when the Model PD07016 fails to produce the required high-voltage output such as during current limit or short circuit load conditions.

Limit/Trip Status
An indicator will illuminate and a BNC will provide a TTL low when the high-voltage output is disabled due to the output current exceeding the current trip level, the detection of a high-voltage supply fault, the removal of one of the panels, or if the Model PD07016 is out of regulation for greater than 500 ms.

Settling Time (to 1%)
Less than 200 µs for a 0 to 10 kV step.

Voltage Monitor
A buffered output providing a low-voltage replica of the high voltage output.

• Scale
  1/1000th of the high-voltage output signal.
• DC Accuracy
  Better than 0.1% of full scale.
• Offset Voltage
  Less than ±5 mV.
• Output Noise
  Less than 20 mV rms (measured using the true rms feature of the Hewlett Packard Model 34401A digital multimeter).
• Output Impedance
  47 Ω.

Current Monitor
A buffered output providing a low-voltage representation of the load current.

• Scale
  30 mA/V.
• DC Accuracy
  Better than 2% of full scale.
• Offset Voltage
  Less than ±10 mV.
• Output Noise
  Less than 30 mV rms (measured using the true rms feature of the Hewlett Packard Model 34401A digital multimeter).
• Bandwidth (-3db)
  DC to greater than 5 kHz.
• Output Impedance
  47 Ω.

GENERAL

Power Requirements

• Line Voltage
  Factory set for one of two ranges:
  104 to 127 V AC or 180 to 250 V AC, at 48 to 63 Hz (specify when ordering).
• Power Consumption
  1800 VA, maximum.

Operating Conditions

• Temperature
  0 °C to 40 °C.
• Relative Humidity
  To 75%, noncondensing.

Dimensions
91.4 cm H x 43 cm W x 87 cm D
(36” H x 17" W x 34" D).
Depth dimension includes handles and
20 cm (8") of spacing bars to insure
proper airflow to the fans on the unit.

Weight
73 kg (160 lb) approximate.

High-Voltage Output Connector
Caton high-voltage connector.

Amplifier Input
BNC connector.

Voltage Monitor Connector
BNC connector.

Current Monitor Connector
BNC connector.

Remote High-Voltage On/Off Connector
BNC connector.

Out of Regulation Status Connector
BNC connector.

Fault/Trip Status Connector
BNC connector.

AC Line Receptacle
Standard IEC 320 three-prong AC line connector.

CERTIFICATION

All specifications are with no load unless otherwise noted.
All specifications are subject to change.